• How can I test if Spooky2 Scalar is working?
• Can anyone tell me what is the ideal tuning frequency?
• If the button on the receiver was off during a bfb scan and during a rife treatment (but the transmitter had been tuned) does that mean nothing happened?
• I find that the brightness of the tuning light on the Receiver is very sensitive to the lid angle.
• Why can we still tune scalar when we don’t connect the transmitter and receiver with link cable?
• I turn on Scalar, I turn the knob counter clockwise until the light is at it’s brightest. I’m at 5.6 then I turn the knob counter clockwise until the light goes off? I’m at 2.0 now? Is this correct?
• What happens when Scalar is turned on and not tuned? Does it reset to 8.0 Mhz during a power outage? Is it pumping out dangerous levels of EMF radiation?
• When should I worry about tuning point?
• I used two different tuning methods, using method one produced 6.10MHz, using method two produced 5.65Mhz. How do I know which one is most accurate?
• Can computers be in the Scalar field? Do you have to retune it at some point other than when you move it to a different position?
• How do I tune using the Tuning light? If both antennas are up and facing each other and placed in position across the room, I cannot see the light on the receiver while turning the tuning knob on the transmitter. But if I turn the receiver so I can see th
• When I tune my device, so that I get the light at the receiver, sometimes I have to go lower than 5, sometimes 4.70. The lights at the transmitter would look fine at 5.5. What shall I do?
• The tuning method 2 need 2 persons or 1 person with mirror. I cannot see the tuning light during the tuning (operation distance 6 feet).
• Does the LED on the receiver exclusively light up when the scalar signal is established?
• Why do I tune to the 528 Hz frequency but never manage to get that frequency?
• Do we need to make sure the link cable is not in the scalar field?
• Does it mean using my body very close to the transmitter would affect the strength of scalar energy?
• If I use the long link cable, I get a reading of between 6.0-6.2 using tuning mothod 1 on the transmitter, but the light on the receiver is not illuminated.
• I tune Spooky2 Scalar correctly, then after an hour when I push the button on the receiver, it does not light up anymore. Then I tune it a bit clockwise and it lights up again on maximum. Then it stays tuned. I guess it has to do with the temperature that
• If using crystals, essential oils, or other things on the Receiver coil, do you tune before or after placing them on the Receiver coil?
• At my found tuning-frequency of 5.5 MHz using method1, the tuning light on my receiver is not lighting red at all. Is this still the perfect frequency, or should the red receiver light better glow up a little bit?
• Previously it was recommended that as the dial reached the point where the tester coil lights were barely lit, that was not the final attunement. We were told to turn the dial clockwise 2 clicks. That would be the true attunement point. So which is the co
• How do I know my Spooky2 Scalar is producing a scalar field? It is strange that I can “Tune” the transmitter even with the Receiver’s cable disconnected. How does the Spooky2 Scalar carry the electrons?
• I have two coil testers. One coil tester shows 5.7 MHz. The other shows 6.1 MHz. Is this correct?
• I have 2 scalar units and have a problem with inaccurate LED coil tuners. They do not tune to the same frequency. One tunes to 6.45mhz and the other tunes to 5.95mhz.
• If I want to do the imprinting water, should I place the water first and then do the tuning?
• Where is the optimal scalar wave tuning after the water glass is removed?